The DJI Avinox M2 is a lightweight, full-power eMTB mid-drive rated by Avinox at up to 1,100 W peak power and 125 Nm peak torque, with an approximate motor weight of 2.65 kg. It sits below the M2S flagship in Avinox’s second-generation lineup. Those peak figures are manufacturer claims, not independently verified M2 test results; EMTB Forums reported 110 Nm as the regular torque figure in its 2026 summary.
How powerful is the Avinox M2?
Avinox’s April 9, 2026 launch information gives the M2 a claimed 1,100 W peak output and 125 Nm peak torque. EMTB Forums reports 110 Nm as the regular figure and 125 Nm in Boost, as well as a 250 W continuous rated power figure. These numbers describe different operating and rating contexts, so peak output should not be read as continuous power.
| Figure | What it means | Reported value and source |
|---|---|---|
| Peak power | Maximum stated output, not continuous output | 1,100 W, claimed by Avinox in 2026 |
| Regular torque | Torque outside the reported Boost peak | 110 Nm, reported by EMTB Forums in 2026 |
| Boost peak torque | Peak torque in Boost | 125 Nm, claimed by Avinox and reported by EMTB Forums in 2026 |
| Continuous rated power | Nominal rating cited for the system | 250 W, per EMTB Forums’ 2026 summary of the system specification |
| Motor weight | Motor only, not the complete bicycle | Approximately 2.65 kg, claimed by Avinox in 2026 |
How much of that performance is independently verified?
EMTB Forums says no laboratory had dyno-tested an M2 in isolation when it published its 2026 summary. The cited peak figures are therefore manufacturer claims, not independent measurements. M2-specific acceleration, sustained climbing output, thermal derating and efficiency remain unestablished by those sources. Do not treat testing or riding reports about the M2S as evidence for the M2.
Is the Avinox M2 better than Bosch CX?
The available M2 figures are not enough to declare it better than Bosch CX. A meaningful comparison requires tests of the exact motors under comparable conditions, plus the complete bikes they are installed in. The cited material provides no equivalent Bosch CX measurements or M2-specific independent dyno results.
#1 Best Overall
- Ultralight Carbon Construction with ASTM 5 Approval - Highest strength-to-weight ratio in e-MTB world at 320-357g depending on motor compatibility, strong enough for bike park shuttle days
- Wide Motor System Compatibility - Works with 24mm ISIS, 30mm ETOR, and SRAM DUB spindles including Bosch, Brose, DJI Avinox, TQ, Specialized, and Fazua motors
- Dual Offset Options for ISIS Motors - Choose 26mm offset (optimized for Bosch CX Gen4/Gen5) or 21.5mm offset (optimized for Bosch SX, Brose S-Mag, DJI Avinox, TQ HPR50, Specialized 2.2 & 3.1)
- Three Progressive Arm Lengths - Available in 155mm, 160mm, and 165mm to accommodate different rider sizes and preferences (155mm for ISIS 26mm offset and Fazua only)
- Complete Installation Package - Includes crankset, two molded crank boots, sticker, and comprehensive user manual for hassle-free installation
What to compare on complete bikes
- Output: separate peak watts and torque from the nominal continuous rating, and check how each bike’s assist modes are tuned.
- Mass: the M2’s approximate 2.65 kg figure is for the motor, not the full eMTB. Compare complete-bike weights in matching sizes and configurations.
- Delivery: responsiveness, controllability and Boost behavior are ride characteristics; the cited peak numbers do not establish which system feels better.
- Long climbs: look for comparable sustained-output and thermal-derating data, rather than assuming peak output continues indefinitely.
- Noise and drag: consider gear design, sound measurements and unassisted pedalling resistance, while checking that the figures use comparable test methods.
- Ownership: compare the frame and suspension package, geometry, warranty, local dealer support and replacement-battery availability—not torque alone.
What is different about the M2?
The M2 retains the M1’s compact form and uses helical, dual-engagement gearing. Avinox says the helical gears reduce knocking and rattling, and reports 4.6% higher power density than the M1. Its launch material gives a sound-pressure figure of ≤45 dBA for the new drive systems, but not a separately measured M2 result. BikeRadar reports sealed bearings and a 41% reduction in unassisted riding resistance; that figure is a reported comparison, not a measurement established here under specified test conditions.
The M2 is the mid-range second-generation motor; the M2S is the flagship, rated by Avinox at 1,500 W peak and 150 Nm peak torque. Those M2S ratings and any M2S test results should not be transferred to the M2.
Rank #2
- Compatible Model: The wheel speed sensor grille is compatible with DJI Avinox M1/M2/M2S motor.
- Bike Frame compatibility: Compatible with Amflow/Velduro/Teewing E‑MTB Frame
- 0.8 mm Thinned Improved Design: Thinned from the OEM 1.2 mm thickness, creating a 0.6 mm clearance between the wheel‑speed sensor probe and trigger disc after installation.
- Compatible with Floating Brake Rotors: Compatible with Hope‑series floating rotors, increasing the reserved clearance between the wheel‑speed sensor probe and trigger disc.Also works with standard solid brake rotors for direct installation.
- Note: Size is manual measurement, there are exist errors.
Which batteries and displays work with the M2?
Avinox pairs the M2 system with removable RS800 (800 Wh) and RS600 (600 Wh) batteries, along with new displays and the Ride App. This makes the M2 part of an integrated bike system rather than just a motor choice.
| Battery | Capacity | Practical consideration |
|---|---|---|
| RS800 | 800 Wh | The larger-capacity option for riders prioritizing distance and long climbs. |
| RS600 | 600 Wh | The lower-capacity, lighter option for riders prioritizing lower battery mass or shorter rides. Avinox says it can be mounted externally as a dual-battery setup on supported bikes. |
Battery fit, charger type, regional stock and replacement cost depend on the particular bike and market. Confirm the exact frame’s approved configuration and the local availability of compatible parts before buying; do not assume that batteries or displays interchange across bikes just because they use Avinox.
Recommended Free Tools
Rank #3
- Compatible Model: Compatible with new DJI Amflow/Teewing e-bike. Only compatible with DJI Avinox M2S and M2 motors. Equipped with original 4-pin plug, compatible with SRAM AXS Electronic Rear Derailleur
- Direct Power Supply from E-Bike Battery: No extra battery installation required. It draws power straight from the bike’s built-in battery.Activates the motor automatic shifting function once powered, delivering smoother, intelligent gear changes.
- 78cm Waterproof Long Cable: This shift cable measures 78 centimeters in total length with full waterproof performance. Its top housing is 3D printed using carbon fiber-filled material.
- Attention: 1.The product may be upgraded from time to time, and the appearance may change without affecting usability. Kindly confirm your actual demand for this product in advance. 2.3D printing products may have some flaws on the surface; it is normal and will not affect their use.
Displays and app functions
The DP100-F and DPC100 displays support route import and turn-by-turn guidance. Avinox says the DPC100 can integrate with Apple’s Find My ecosystem. Through the Ride App, riders can adjust assist level, start assist, continued assist and maximum torque; the app also provides health-management alerts for faults.
Which eMTB bikes use the Avinox M2?
Avinox said in its April 9, 2026 release that more than 60 OEM partners had integrated the M2/M2S systems. Named brands include Amflow, Atherton, BH, Canyon, Commencal, Forbidden, Megamo, Mondraker, Pivot, Propain, Rotwild and Whyte. That announcement concerns the two-system family; it does not establish that every named brand has an M2-equipped model on sale in every country.
Rank #4
- 𝐈𝐦𝐩𝐨𝐫𝐭𝐚𝐧𝐭 𝐑𝐞𝐦𝐢𝐧𝐝𝐞𝐫: Only compatible with DJI Avinox M1 motors, 90cm version used for Velduro e-bike frame, Note: The hole dust plugs are used for DJI Amflow PL only.
- replacement Power cable Compatible with DJI Avinox M1 SRAM AXS: custom fit for first-generation DJI Avinox M1 e-bike motor, fully compatible with SRAM AXS electronic rear derailleur, directly draws power from vehicle built-in battery to activate auto shift function
- High durable shift cable & shifting wire spare parts, professional e-bike electronic shifting parts Compatible with Amflow, fits for SRAM AXS auto shift system of Avinox M1 drive motor
- Fully Compatible with AMFLOW motor power supply and automatic shifting functions.
- E-bike electronic shifting cable is waterproof.
Check the exact model and specification before choosing a bike: a brand may offer different Avinox motors, battery sizes or equipment across models and regions. For a real purchase decision, verify local availability, dealer and warranty support, replacement-battery supply, and the bike’s geometry, suspension and complete weight.
Independent reader supportYour contribution helps us test, update, and keep practical guides available for everyone.Can you buy the Avinox M2 motor separately?
The cited material presents the M2 as an OEM-integrated drive system used in complete eMTBs, not as a standalone consumer motor purchase. It does not establish a retail path for buying the motor separately. For a replacement or repair, contact the bike’s manufacturer or an authorized local service provider and confirm parts availability for the exact frame and system configuration.
Quick wins for a faster PC:
Repair Windows errors before they cause bigger problemsFix Now →Fix the driver behind crashes, sound loss and screen glitchesFind Drivers →Quick Recap
Best Value
- Includes 104 BCD Spider, Bashguard, and AL-7075 Chainring assembly - Complete integrated protection system with 32T and 34T Bashguard/Chainring size options (DJI Avinox 34T only)
- Compact, integrated aesthetic - Compatible with TQ HPR50, Fazua Ride 60, Bosch SX, and DJI Avinox systems (Bosch SX model also compatible with Bosch CX Gen 4)
- Compatible with 104 BCD alloy or steel chainrings - From any brand for simple and affordable chainring service with less waste
- M4 narrow-wide tooth profile - For superior chain retention, long wear life, the included Helix chainring is compatible with Shimano, TRP, and SRAM 11/12-speed drivetrains (including T-type)
- Turbocharger Race e*spec | 104BCD Spider plus Bashguard | 34T 104 BCD Aluminum Chainring | DJI Avinox | 55mm CL | 8mm Offset | Incl. Bolts and Nuts | Black
Product prices and availability are accurate as of the date/time indicated and are subject to change. Any price and availability information displayed on Amazon at the time of purchase will apply.
